Command 2 0 Dx Update Cd Key
Command 2 0 Dx Update Cd Player
Comand 2.0 Dx Update Cd Download

Mercedes-Benz Comand Navigation System CD ROM Map 9 South East USA 7/00 NEW B475. MERCEDES BENZ NAVIGATION SYSTEM CD S CLK E CLASS 2009 UPDATE. Home » Navigation Software » Search by Car Brand » Mercedes Navigation Software » Mercedes CLK 1999 Navigation CD » Mercedes CLK 1999 TravelPilot DX Comand APS 2.0 v1 CD $ 189.43 $ 101.00 Mercedes Sat Nav CD Germany + MRE incl. Travel Guide MERIAN. COMAND 2.0/COMAND 2.0 MOPF The same COMAND 2.5 technology (with DX navigation maps) was next incorporated in a somewhat different form factor known as COMAND 2.0 (with '2.0' referring to the fact that this modified unit had a 2 DIN height), but with the cassette drive removed.

!! Please select country!!

Created: 15 May 2007

Command 2 0 Dx Update Cd Key

Last Updated: 11 Sep 2007

Command 2 0 Dx Update Cd Player

Comand 2.0 Servicing and Disassembly

This document describes how to dismantle your COMAND 2.0 unit. It helps you to clean the CD mechanism or to replace any broken bits.

Often COMAND 2.0 systems fail because the laser lens has become dirty - using this document will help you to clean the laser lens. Also, if the roller becomes greasy then COMAND will fail to eject the CD reliably.

It is important you dismantle COMAND in the correct order, otherwise you end up bending bits, and it will never quite be the same.

COMAND has 3 seperate sections

The front - mainly contains the buttons.
The top section, contains the CD and navigation system
The bottom section contains the rest, including amplifier, tuners etc.

It is important to remove the front section first, before removing top or bottom covers, or they bend.

Please also note that this was all done using proper anti-static precautions - I suggest getting a wrist strap and an earthing lead/plug from RS components (www.rswww.com) or Maplin.

1 - Removing the front

Firmware 1416 (fdp1cn1416ar). Remove the 2 torx screws holding the clip bracket at the front on the left hand side of the unit.

Note that The picture below shows a ML/CLK COMAND with the clip brackets, the E class one has other right angle brackets.

Here is the right hand side with the screws removed. The mounting brackets then unclip from the unit.

Having removed the brackets and 4 screws you will see one more screw under each bracket and one that was above each of the brackets - it is these that hold the front section in place.

Having removed those 4 screws (two on each side) you can then seperate the front from the rear by pulling the front straight out. It is important that it is pulled squarely and straight to protect the connector. Here is a picture of the rear of the front section when it is removed.

2. Seperating the top and bottom sections

Carefully pull out the red connectors which connect the wiring between the sections, pull them straight toward you - its a bit fiddly.

And remove the bracket on the left at the back by removing the two torx screws

You now have the COMAND unit seperated into it's 3 different modules. You can remove the covers of the modules by gently levering it up all the way round.

3. Inside the bottom section

Here is the bottom section with it's lid removed

That is about as far as you can dismantle the bottom section without a soldering iron.

4. Dismantling the front section

Referring to the picture of the front section above, pull out the white connector at the right of the circuit board (this is the backlight power connection).

Then using a pliers squeeze the protruding part of each of the 5 white clip-posts (roughly at each corner of the circuit board and one in the middle on the lower edge) and pull the board up just far enough to stop the clip in the post returning to its original position. Once all clips are released pull the board upward squarely (otherwise connectors will bend) - this is what the unit then looks like. I have also remove the connector, which is on the left of the picture.

You can now remove the 4 small screws (one in each corner) and seperate the keyboard section from the display section

Dismantling the rest is just a case of undoing the screws.

5. Dismantling the top section

Heres a picture of the top section, note that I have already removed the four torx screws that hold the CD changer mechanism in place.

Before removing the CD changer you will also have to unscrew the GPS aerial connection, that is done by removing the black torx screw you can see at the bottom left of the picture (on the rear panel of the COMAND, above the grey square GPS antenna connector).

As you remove the CD changer you will need to unclip the 3 way green connector that goes to the black gyroscope that is attached to the left side (in above picture) of the top unit.

Free ex4 to mq4 decompiler software testing. Having remove the CD changer, the top section looks like this - you can see the gyroscope with its 3 wire green connector in the picture.

6. Dismanting the CD drive

This is the underside of the CD drive, which shows the navigation processor board (the larger circuit board), the GPS board (bottom left) and the cable to the GPS antenna socket.

To remove the circuit board, disconnect all the connectors - the ones with ribbon cables have a sliding lock that you slide in the direction of the cable, and then the cable will pull out really easily.

Then remove the 4 torx screws and remove the navigation PCB

The GPS receiver circuit is held in place by the plastic frame around it, and can be removed by gently bending that plastic frame by the clips that hold the litlle circuit board.

Having removed the navigation PCB you can now get at most of the CD changer mechanism.

You now need to carefully unook the two springs circlied in red in the picture below, noting their exact orientation (otherwise they will drop off once you put a CD in !), and remove the two gold head small screws that are circled in blue in the picture.

You can then carefully pull out the roller mechanism. You should clean the roller and the white plastic section with surgical spirit and a clean lint-free cloth.

Having removed the roller, you can get at the CD laser lens with a cotton bud dipped in surgical spirit. You can not easily see the lens, but it is on the other side of the black mechanism with the larger ribbon cable.

Here is a picture of a removed laser mechanism so you can see the lens - do not try and remove the laser mechanism to clean it though.

7. Reassembly

And, finally, in the words of the wise, re-assembly is the reverse of the disassembly.

The most difficult bit is getting the roller mechanism back in place, it must sit in the two rectangular locating holes along the top edge of this picture

When you re-insert the roller mechanism, it should be in the following position

And, really finally, here is a picture showing the orientation of the springs which is very very important

Please don't blame me if you break your COMAND unit, it is completely up to you whether you want to risk taking yours apart.

If you found this information useful, please support the site by making a donation via Paypal. Any amount at all helps me improve the information on the site.

Comand 2.0 Dx Update Cd Download

Comand Online Ltd - the place to buy Mercedes iPod kits, phone kits, retrofit parts & map disks
MY AUTOCAR - THE BEST PLACE TO TALK